D-Jetronic Pressure Sensor 0280100111: M110 W116 R107 280 models
Share
The Mercedes 280 SE, 280 SL or 280 E with D-Jetronic runs rough, smokes or uses noticeably more fuel than before – and the search for the cause quickly leads to an inconspicuous component in the engine bay: the pressure sensor. It is the most important measuring element of the D-Jetronic. This guide shows how to recognize a faulty pressure sensor, what you should check yourself beforehand, and why the Bosch suffix number is decisive when replacing it.
Symptoms
The pressure sensor measures the vacuum in the intake manifold and reports it to the D-Jetronic control unit via two coils. From this signal the control unit forms the basic injection time. If the sensor delivers a wrong signal, the mixture is off across the entire part-load range.
| Symptom | Likely cause |
|---|---|
| Engine constantly runs too rich, black smoke, high consumption | Pressure sensor delivers wrong signal or vacuum hose leaking |
| Engine runs lean, stumbles at part load, responds poorly to the throttle | Pressure sensor, altitude correction out of adjustment or false air at the intake manifold |
| Rough idle, CO value cannot be set cleanly | Pressure sensor, vacuum hose or connector with contact resistance |
| Lack of power only at full load | More likely the throttle switch – this sensor has no full-load diaphragm |
| Engine does not start at all, no injection | More likely the control unit or power supply – see Checking the D-Jetronic control unit |
Causes
The pressure sensor works with pressure capsules that expand depending on intake manifold pressure and move an armature between two coils. After fifty years in the engine bay, the capsules age, the solder joints of the coils suffer from heat and vibration, and the housing corrodes at the rivets. Often the sensor itself is not to blame: a porous vacuum hose lets false air into the measuring line, the sensor “sees” less vacuum, and the control unit injects too much fuel.
Another source of error is the altitude correction under the black cap. If it was turned to mask another problem, the basic setting is no longer correct. And last but not least, sensors with the wrong suffix number have been installed over the years – with a characteristic curve that never matched the engine.
Testing it yourself
- Check the vacuum hose: Check the hose between the intake manifold and the pressure sensor for cracks, hardening and a firm fit. This is the cheapest and most common cause.
- Read the Bosch number: Does the type plate read 0 280 100 111? A sensor with a different suffix number has a different characteristic curve and does not suit the M110.
- Check connector and cable: Contacts for corrosion, cable for broken insulation. Contact resistance distorts the signal.
- Rule out the throttle switch: On these engines it reports idle and full load. A wrongly adjusted switch resembles a sensor fault.
- Measure the coils: Check both windings at the connector for continuity with a multimeter and compare with the specifications from the workshop manual. A broken winding means replacement.
Solution
If the pressure sensor is confirmed as the cause, the only remedy is replacement with a sensor with exactly the Bosch number 0 280 100 111. New parts have not been available for a long time, so used genuine parts are the realistic option. We have an original Bosch pressure sensor 0 280 100 111 in stock: used genuine part with riveted housing halves and black protective cap, type plate rubbed off, bracket with rust spots. The photos show exactly the part you will receive. It is a one-off piece – you will find more parts around the injection system in the category Fuel system & injection.
Not to be confused with: 0 280 100 112 (450 SE/SEL/SL/SLC), 0 280 100 012 with full-load diaphragm (350 SL, 280 SE 3.5) and 0 280 100 006 / 025 (250 CE, M114) do not fit.
Bosch pressure sensor D-Jetronic M110
Part number: 0 280 100 111 (Bosch)
199,00 €
To the pressure sensorCompatible vehicles
Only for engines with D-Jetronic – later 280 models with K-Jetronic have no pressure sensor.
| Model series | Models | Engine |
|---|---|---|
| /8 W114 with D-Jetronic (1972–1976) | 280 E (114.062), 280 CE (114.072) | M110 |
| S-Class W116 with D-Jetronic | 280 SE, 280 SEL | M110 |
| SL R107 / SLC C107 with D-Jetronic | 280 SL, 280 SLC | M110 |
More parts for these vehicles: W116 · W107 / R107. Also relevant to the same engine is our guide to the M110 intake manifold.
FAQ
How do I know whether my pressure sensor is the 0 280 100 111?
The Bosch number is on the type plate on the housing. If it is rubbed off, engine and model year help: the 0 280 100 111 belongs to the 2.8-liter six-cylinder M110 engines with D-Jetronic. If in doubt, send us your VIN (chassis number).
Does the pressure sensor also fit the V8 engines (350, 450)?
No. The V8 engines need sensors with a different characteristic curve, such as the 0 280 100 112 for 450 SE/SEL/SL/SLC or the 0 280 100 012 with full-load diaphragm for 350 SL and 280 SE 3.5.
Does every 280 SE or 280 SL have a pressure sensor?
No. Only engines with D-Jetronic have a pressure sensor. Later 280 models with K-Jetronic work with a mechanical fuel distributor and do not need this part.
Can I change the characteristic curve of a different pressure sensor?
No. Sensors with a different suffix number have a different characteristic curve and cannot be converted for the M110. The screw under the black cap is the altitude correction, not a characteristic curve adjustment.
What should I check before replacing the pressure sensor?
First the vacuum hose to the intake manifold for cracks and a firm fit, then the connector and the throttle switch. Only when these points are fine is replacing the sensor worthwhile.
KFZTeile-Thot is a specialist business for tested and refurbished Mercedes parts with its own test benches and has over 1.000 positive eBay reviews. Not sure whether the pressure sensor fits your car? Send us your VIN (chassis number) and model year – by phone at +49 179 8991069 (Mon–Fri 8 am–6 pm) or via our contact form.