M123 crankshaft 123 031 03 01 – Buyer's guide W123 250 / 250 T
Share
Anyone taking apart a W123 250 quickly notices: the 2.5-liter six-cylinder M123 is an oddball. It was only fitted in the W123 250 and in the 250 T wagon, and on the used market its parts are easily confused with those of other Mercedes six-cylinders – such as the 280 E (M110) or the older W114 250. After a bearing failure, the question is therefore usually: can the existing crankshaft still be ground, and if not, which crankshaft really fits? This buyer's guide shows how to recognize damage, which numbers to compare and what the offered crankshaft fits.

Genuine M123 crankshaft (casting number 123 031 03 01) with sprocket, front hub including center bolt and bolted-on flywheel for manual transmission.
How do you recognize wear or damage?
The crankshaft converts the reciprocating motion of the six pistons into rotary motion and drives the timing chain at the front via the sprocket. The flywheel smooths out running, carries the starter ring gear and is the friction surface for the clutch. In the M123 the crankshaft has four main bearings. Whether it can be reused usually only becomes clear once the engine is disassembled.
| Finding | Meaning |
|---|---|
| Deep scoring or discoloration on main journals or crankpins | Bearing damage, usually after oil starvation – measure the shaft, grind or replace if necessary |
| Journals already ground to the last repair size | No further grinding possible – replacement shaft required |
| Crack or runout error during inspection | Shaft no longer usable |
| Wear marks and scoring on the flywheel friction surface | Have the flywheel resurfaced; the crankshaft itself may be fine |
| Broken teeth on the starter ring gear | Check the ring gear or flywheel – not crankshaft damage |
| Not to be confused with: Rattling at the front of the engine shortly after a cold start | Usually the timing chain or chain tensioner, not the crankshaft – our guide explains the principle Chain tensioner: timing chain rattles (W115/W123) |
Causes
After decades and high mileages, the bearing journals are the main issue. Oil starvation, overly long oil change intervals or worn bearing shells leave scoring on the journals. On engines that have been overhauled before, the crankshaft has sometimes already been ground to undersize, so no further grinding is possible. Because the M123 was only fitted in one model series, suitable crankshafts are rare. A used genuine crankshaft with clean journals is therefore an economical basis for many rebuilds – provided it is measured before installation and checked for cracks and runout.
What to look for when buying
- Identify the engine: The M123 has an 86 mm bore and a 72.45 mm stroke and has four main bearings. W114 250 / 250 C (M114, M130) as well as 280, 280 E and 280 SE (M110) have seven-bearing crankshafts with a 78.8 mm stroke – they are not interchangeable. For the M110 there is a separate M110 crankshaft buying guide.
- Compare the casting number: The offered crankshaft bears casting number 123 031 03 01, and the material code 49MnVS3 is stamped on the web. Compare the number with your crankshaft. For the long-wheelbase 250 (V123), please be sure to check the casting number or send us the engine number.
- Mind the transmission: The included flywheel is for manual transmissions. Cars with automatic have a drive plate instead of the flywheel.
- Assess the condition realistically: Main and rod journals are bare metal with oil and dirt residue and slight discoloration, without deep scoring in the photos. The journals have not been measured, and no crack or runout check has been done. The flywheel has a complete starter ring gear but signs of use – resurfacing is recommended.
- Check the scope of delivery: Crankshaft with sprocket and front hub including center bolt, plus bolted-on flywheel. Bearings, pulley and vibration damper are not included.
Solution
If your shaft is beyond saving, a used genuine shaft with the matching casting number is the obvious basis. We offer the M123 crankshaft 123 031 03 01 with flywheel for manual transmission for 179 € offered. According to the old marking on the flywheel (“Merc. 250 /123 129PS”), it comes from a W123 250 with 129 hp. Due to its weight and size, this part is available for pickup only; we arrange the appointment after purchase, and a viewing beforehand is possible by arrangement. The photos show exactly the part you will receive.
The crankshaft is a one-off piece. If it has already been sold, you will find more parts for these vehicles in the category W123. For the W123 diesel models, read the OM616/OM615 crankshaft buyer's guide.
M123 crankshaft 123 031 03 01 + flywheel
Used genuine Mercedes part for W123 250 / 250 T with manual transmission – 179 €, pickup only.
View offer →Compatible vehicles
| Model series | Models (engine M123 only) |
|---|---|
| W123 sedan (1976–1985) | 250 with 129 hp (until 1979) and 140 hp (from 1979) |
| W123 T-Modell wagon S123 | 250 T |
The flywheel is only for manual transmissions. For the long-wheelbase 250 (V123), please compare the casting number. Does not fit W114 250 / 250 C (M114, M130), 280 E, 280 CE, 280 SE (M110), 230.6 (M180) or any diesel engines. If in doubt, send us the engine number or VIN – we check fitment free of charge.
FAQ
What is the casting number of the M123 crankshaft?
The offered crankshaft bears casting number 123 031 03 01. Compare this number with your removed crankshaft or send us the engine number – we check fitment free of charge.
Does the crankshaft also fit the W114 250 or the 280 E?
No. The W114 250 and 250 C have the engines M114 and M130 respectively, the 280 E the M110 – all with a seven-bearing crankshaft and 78.8 mm stroke. The M123 crankshaft has four main bearings and only fits the W123 250 and 250 T.
Can I use the flywheel with an automatic transmission?
No. The included flywheel is for manual transmissions. Cars with automatic have a drive plate instead of the flywheel.
Has the crankshaft been measured and tested?
No. The bearing journals have not been measured, and no crack or runout check has been done. Have the crankshaft checked by an engine rebuilder before installation; the flywheel should be resurfaced.
Is the crankshaft shipped?
No. Because of its weight and size, this part is available for pickup only. We arrange the appointment after purchase, and a viewing beforehand is possible by arrangement.
KFZTeile-Thot is a specialist business for tested and refurbished Mercedes parts with its own test benches – specialized in Mercedes classic cars, with over 1,000 positive eBay reviews. Questions about fitment of the M123 crankshaft? Call us: +49 179 8991069 (Mon–Fri 8 am–6 pm) or use the contact form.