Original Bosch Airbag-Steuergerät A 004 820 18 10 für Mercedes W124, W126 und R129 mit Beifahrerairbag

W124/W126/R129 SRS light on? Airbag control unit A0048201810

Short answer: If on your W124, W126 or R129 with driver- and passenger airbags the SRS warning light stays on after the engine starts and a fault in the airbag control unit cannot be cleared, the control unit itself is often the cause. For this equipment, the number is A 004 820 18 10 (Bosch 0 285 001 031). The solution: a used genuine Bosch control unit for 249,00 € – read out the fault memory first and compare the number on your own unit.

The SRS light will not go out, and when searching for the right spare part, two almost identical numbers come up: A 004 820 17 10 and A 004 820 18 10. The difference is decisive, because it depends on your vehicle's airbag equipment. This guide covers the unit for vehicles with driver and passenger airbags. If your car has only a driver airbag, read our guide on the Airbag control unit A 004 820 17 10.

Used genuine Bosch SRS airbag control unit A 004 820 18 10 (Bosch 0 285 001 031) for Mercedes W124, W126 and R129 with passenger airbag

Genuine Bosch SRS airbag control unit A 004 820 18 10 for vehicles with driver and passenger airbags.

Symptoms

With its built-in acceleration sensor, the control unit measures the vehicle's deceleration. In a crash it fires the driver and passenger airbags as well as the seat belt pretensioners. It also continuously monitors the restraint system and controls the SRS warning light in the instrument cluster.

Symptom Likely cause
SRS warning light stays on after the engine is started Fault in the restraint system – often the airbag control unit
Fault in the airbag control unit cannot be cleared and keeps returning Airbag control unit defective
SRS light stays on after an airbag deployment Control unit locked after deployment – replacement required
Several warning lights stay dark or show nonsense More likely the Indicator unit in the instrument cluster, not the airbag control unit
Faults in several control units at the same time, voltage problems More likely the overvoltage protection relay or the on-board voltage

Causes

The Bosch control units of this generation are around three decades old. Electronic components age, solder joints fatigue from temperature changes and vibration, and the unit's self-diagnosis reports such deviations as faults. Then there is the installation location: the unit sits on the transmission tunnel under the center console, on the R129 in front of the selector lever. Moisture in the footwell, for example from leaking doors or windows, stresses the housing and connector strip. After an airbag deployment the unit is locked anyway and must be replaced.

Testing it yourself

Important: The restraint system contains pyrotechnic components. Never measure at airbag or belt tensioner circuits with a multimeter, and work on connectors only with the battery disconnected. If in doubt, leave the work to a specialist workshop.

  1. Observe the lamp test: After the ignition is switched on, the SRS light comes on briefly and goes out. If it stays on or comes back while driving, the control unit has detected a fault.
  2. Check the on-board voltage: A weak battery or fluctuating charging voltage can trigger faults in control units. This check costs nothing.
  3. Check the connector and installation position: With the battery disconnected, check the connector for a firm fit, moisture and corrosion. The arrow on the housing marks the prescribed installation position.
  4. Read out the fault memory: Only reading it out shows whether the control unit itself or another part of the system is being reported. If an internal control unit fault persists after clearing, replacement is due.
  5. Compare part number and equipment: A 004 820 18 10 belongs to vehicles with driver and passenger airbags, A 004 820 17 10 to vehicles with a driver airbag only. The two units are not interchangeable.

Solution

We have a used genuine Bosch control unit A 004 820 18 10 (Bosch 0 285 001 031) in stock, housing and connector strip undamaged, for 249,00 €. It is a genuine Bosch part, not aftermarket. As a successor number, Mercedes-Benz lists A 000 820 69 26.

Please note these distinctions before buying:

  • Not for model year 1994/95: W124 and R129 from model year 1994 have newer control units (for example A 000 820 71 26 / 72 26).
  • Do not mix Bosch and Temic: According to Mercedes, control units and sensors from Bosch and Temic must not be combined.
  • Does not fit for the 190 W201 (no passenger airbag), the W140 S-Class (A 000 820 70 26 or A 001 820 19 26) as well as W202, W210, R170 and W208 (Temic control units).
  • Engine: The control unit depends on the airbag equipment, not on the engine. For models not listed here, please compare the number on your own unit.
Genuine Bosch airbag control unit A0048201810 for Mercedes W124 W126 R129 with passenger airbag

Airbag control unit A 004 820 18 10

Genuine Bosch 0 285 001 031 for vehicles with driver and passenger airbags – 249,00 €, single piece from stock.

To the control unit →

The unit is a single piece. You will find more control units and relays for classic Mercedes in the category Mercedes relays & control units as well as sorted by model series under W124 and W126.

Compatible vehicles

Only for vehicles with driver- and and passenger airbags.

Model series Models
E-Class W124 / S124 / C124 (up to 06/1993) 260 E, 280 E, 300 E, 320 E (also 4MATIC and 300 E-24), 300 D, 300 TE / 320 TE (also 4MATIC), 300 CE / 320 CE, 400 E, 500 E
S-Class W126 / C126 300 SE / 300 SEL, 420 SEL, 560 SEL, 560 SEC, 350 SD / 350 SDL
SL R129 (up to 06/1993) 300 SL / 300 SL-24, 500 SL

Not sure? Send us your VIN (chassis number) and model year – we will check the fit for free.

FAQ

What is the difference between A 004 820 18 10 and A 004 820 17 10?

A 004 820 18 10 (Bosch 0 285 001 031) is for vehicles with driver and passenger airbags, A 004 820 17 10 (Bosch 0 285 001 030) for vehicles with a driver airbag only. The units are not interchangeable.

Does the control unit fit a 1994 W124?

No. W124 and R129 from model year 1994 have newer control units, for example A 000 820 71 26 or 72 26. This unit is intended for W124 and R129 up to 06/1993 and the W126.

Where is the airbag control unit installed?

It is bolted to the transmission tunnel under the center console, on the R129 in front of the selector lever. The arrow on the housing marks the installation position.

Does the control unit have to be replaced after an airbag deployment?

Yes. After a deployment the control unit is locked, the SRS light stays on, and the unit must be replaced.

Can I combine Bosch and Temic parts?

No. According to Mercedes, control units and sensors from Bosch and Temic must not be combined with each other. That is why this Bosch unit also does not fit W202, W210, R170 and W208.

KFZTeile-Thot is a specialist business for tested and refurbished Mercedes parts with its own test benches and has over 1.000 positive eBay reviews. Not sure about the part number or your vehicle's equipment? Call us at +49 179 8991069 (Mon–Fri 8 am–6 pm) or write to us via the contact form – with your VIN we check the fit before you buy.

Back to blog

Need help?